When a Waco facility replaces its main switchgear, retires a bank of transformers, or clears an electrical room ahead of a lease turnover, the electrical gear doesn’t just disappear on its own. Someone has to disconnect it from bus and cable, break it down into pieces that can move through doorways and loading docks, and get it off the property in a way that doesn’t damage the building or leave a safety hazard behind. That’s the work USA Decom does for facility owners, plant managers, electrical contractors and property managers across the Waco market.
Electrical equipment removal covers a wide range of gear: low-voltage switchgear and switchboards, molded-case and power circuit breakers, panelboards, transformers, busway, automatic transfer switches, motor control centers and related distribution equipment. Some of it is decades old and simply worn out. Some of it is being replaced as part of a capacity upgrade, a tenant buildout, or a facility-wide electrical modernization. Either way, removing it correctly requires the same care that went into installing it in the first place — plus the added complications of working around live equipment, existing production, and equipment that may weigh several thousand pounds per section.
What Does Electrical Equipment Removal Actually Involve?
Facility managers researching this service usually want to know what’s involved before they call anyone. At a high level, a typical electrical equipment removal project includes:
- Site assessment and scope development — identifying what equipment is coming out, what stays, and what the building’s access constraints look like
- Coordination with the facility’s electrical contractor for lockout/tagout, de-energization and disconnection from upstream and downstream conductors, which typically remains that contractor’s responsibility rather than ours
- Physical disassembly of switchgear lineups, panelboard sections, busway runs and transformer enclosures into manageable, transportable pieces
- Rigging and moving heavier components such as power circuit breaker cells, transformer cores and switchgear vertical sections
- Loadout and transportation from the electrical room or yard to a truck or trailer
- Sorting and disposition of recoverable components, scrap metal and any materials requiring special handling
If you have a project coming up, use the form below to tell our team about the facility, equipment and schedule.
Our team plans and sequences the physical removal work around the disconnection process handled by the customer’s electrician or electrical contractor, so the project moves efficiently once equipment is confirmed de-energized and isolated.
Why Waco Facilities Need This Service

Waco’s economy includes a working mix of manufacturing, food processing, automotive components, heavy equipment and precision fabrication, supported in part by workforce programs at institutions such as Texas State Technical College and McLennan Community College. Facility upgrades in these sectors — new production lines, plant expansions and electrical modernizations — are among the more common reasons older distribution equipment gets pulled out of service to make room for higher-capacity gear.
The region’s industrial parks add another layer of activity. Southwest Waco is home to Texas Central Park, a large multi-tenant industrial and business park along the I-35 corridor, and additional industrial land continues to be developed in surrounding communities. Every time a building in one of these parks is re-tenanted, upgraded to a higher electrical service, or repositioned for a new occupant, the existing switchgear, panelboards or transformers may need to come out — either because they no longer meet the new tenant’s load requirements or because they’ve reached the end of their service life.
Data center and technology projects in the region also involve substantial electrical power distribution infrastructure — switchgear, transfer switches, PDUs and busway among it — which eventually requires professional removal when systems are upgraded, relocated or decommissioned.
What Types of Electrical Gear Do We Handle?
Most of the equipment we’re asked to remove falls into a few recognizable categories. Facility managers often already know the manufacturer and family name of what’s coming out — it helps to describe the project in those terms when reaching out:
- Low-voltage power circuit breakers and switchgear, including Square D/Schneider Electric MasterPact NT and NW breakers, PowerPact and Power-Zone equipment, Eaton/Cutler-Hammer Magnum and Series C breakers, and GE/ABB AK, AKR and Spectra families
- Switchboards and panelboards, such as Square D I-Line boards and panelboards, Eaton Pow-R-Line equipment, and Siemens Sentron or legacy ITE panels
- Transformers, both dry-type and liquid-filled, in the capacity ranges common to commercial and light-industrial buildings
- Busway systems, including I-Line, Pow-R-Way, Sentron and similar bus duct runs that need to be dismantled section by section along their route
- Automatic transfer switches, including ASCO and Cummins/Onan-based systems tied to standby power
- Motor control centers and distribution panels serving process equipment on a plant floor
Amperage and voltage matter for planning purposes. A 400A panelboard removal is a very different job than pulling a 2000A or 3000A switchgear lineup rated at 480V, and medium-voltage gear in the 4.16kV to 13.8kV range introduces additional clearance and handling considerations. Knowing the general voltage class and amperage of the gear helps our team scope crew size, rigging equipment and schedule before a site visit.
How Does Removal Work in an Occupied or Partially Active Facility?
Very few electrical equipment removal projects happen in a completely empty building. Most involve at least one of these conditions:
- A facility that remains partially occupied or operational during the project
- Adjacent electrical systems that must stay energized while the target equipment is isolated
- A limited shutdown window tied to a maintenance outage, weekend, or plant downtime schedule
- Shared building infrastructure, such as elevators, loading docks or corridors, used by other tenants
Sequencing is where experience matters most in these situations. Before any physical demolition starts, our team works through which circuits and equipment sections can be isolated without affecting the rest of the building, what temporary power or bypass arrangements the customer’s electrical contractor may need to maintain critical loads, and how removal work will be staged so it doesn’t block access needed by other trades or occupants. On projects involving switchgear lineups, we often plan removal section-by-section rather than pulling the entire line at once, which limits the footprint of the active work zone and reduces disruption to surrounding operations.
Rigging, Access and Loadout Considerations
Electrical gear is often heavier and more awkward to move than it looks. A single vertical section of low-voltage switchgear can weigh well over a thousand pounds, and a drawout circuit breaker removed from its cell adds concentrated weight in a compact package. Transformers, particularly liquid-filled units, can weigh several tons even in modest kVA ratings.
Before removal begins, we look at:
- Doorway and corridor clearances between the electrical room and the nearest loading area
- Floor loading capacity, particularly on upper floors or mezzanines where heavy gear was originally craned or hoisted into place
- Available rigging points, including whether equipment needs to be skidded, rolled on pipe, or lifted with a forklift, pallet jack or overhead crane
- Loading dock height and truck access, especially at older Waco industrial buildings where dock configurations vary
- Path of travel through the facility, accounting for any obstructions added since the equipment was originally installed
Getting this assessment right before the crew shows up avoids the kind of mid-project surprises — a doorway that’s two inches too narrow, a floor that can’t take a loaded pallet jack — that turn a planned one-day removal into a multi-day problem.
Asset Recovery: What Happens to the Equipment After Removal
Not every piece of electrical gear coming out of a Waco facility is scrap. Depending on age, condition, completeness and manufacturer, some equipment retains resale or reuse value in the secondary market — particularly well-known families like Square D MasterPact breakers, Eaton Magnum DS switchgear, or Siemens WL and Sentron equipment that remain in service across many older commercial and industrial buildings still supported by replacement parts.
Factors that influence whether equipment has recoverable value include:
- Manufacturer and model family, since some lines have stronger demand in the used-equipment market than others
- Physical condition and completeness, including whether trip units, accessories and cradles are intact
- Age and whether the gear is still supported with parts and documentation
- Quantity — a full switchgear lineup or matched set of breakers is often more valuable than a single unit
- Ease of removal and transport, since equipment that comes out cleanly and intact is easier to resell than gear that was damaged during extraction
Where equipment retains recoverable value, that value can help offset a portion of the overall removal cost. We can’t guarantee that every piece of gear will have resale value, or that recovered value will cover the full project cost, but identifying recovery opportunities before demolition begins is part of how we approach these projects. Materials without resale potential are typically segregated for recycling, since copper bus, aluminum housings and steel enclosures all carry recoverable scrap value even when the equipment itself doesn’t.
What Information Helps Us Scope Your Project
Facility managers reaching out about an electrical equipment removal project get a faster, more accurate response when they can share a few basic details up front:
- Type of facility (manufacturing plant, warehouse, office building, data center, etc.)
- What equipment is coming out — manufacturer, model family and quantity if known
- Approximate voltage and amperage ratings
- Whether the equipment is currently energized or already de-energized
- Site access conditions, including dock height, corridor width and elevator availability if applicable
- Target schedule, including any lease turnover, shutdown window or tenant improvement deadline
- Photographs of the equipment and the surrounding electrical room, if available
None of this needs to be exact. Even rough answers help our team understand the scope of the project and start planning a site visit or preliminary discussion.

A Practical Pre-Removal Checklist
Before scheduling an electrical equipment removal project, it helps to walk through the following:
1. Confirm which equipment is being replaced versus which stays in service
2. Identify the electrical contractor responsible for disconnection and lockout/tagout
3. Measure doorways, corridors and elevator dimensions along the planned path of travel
4. Check floor loading in the electrical room and along the route to the loading dock
5. Note any shutdown windows or blackout dates tied to ongoing operations
6. Gather nameplate information — manufacturer, model, amperage, voltage — for the equipment coming out
7. Take photographs of the equipment from multiple angles, including nameplates
Working through this list before a site visit typically shortens the time between initial contact and a usable project plan.
Serving Waco and the Surrounding Region
Beyond Waco itself, we provide electrical equipment removal services throughout McLennan County and the surrounding Central Texas markets, including Temple, Killeen, Hillsboro, Belton, Marlin and communities along the I-35 corridor between Dallas-Fort Worth and Austin. This stretch of the Texas Triangle includes a mix of manufacturing plants, distribution centers, food and beverage production facilities, and technology projects — all of which generate the same kind of electrical equipment removal needs as facilities inside Waco city limits.
Tell Us About Your Project
If you’re planning to remove switchgear, breakers, transformers, busway, panelboards or other electrical distribution equipment from a Waco-area facility, use the form below to tell our team about the equipment, the facility and your timeline. Include the manufacturer and model information if you have it, along with any access constraints or shutdown windows we should know about. We’ll follow up to discuss scope, scheduling, and whether any of the equipment coming out may have recoverable value.


