Plano is home to a mix of corporate campuses, telecommunications and electronics companies, and data center and mission-critical support facilities within the broader Dallas-Fort Worth region. Buildings supporting that kind of occupancy typically carry an installed base of low-voltage switchgear, panelboards, automatic transfer switches, busway and power distribution equipment that eventually reaches the end of its service life, gets replaced during a capacity upgrade, or becomes surplus when a building is repositioned, consolidated or demolished. When that equipment needs to come out, the work looks very different from routine electrical maintenance. It involves de-energization and lockout coordination, rigging of heavy switchgear sections, careful sequencing around active building loads, and a disposition plan for equipment and materials that often retain meaningful recoverable value.
USA Decom provides electrical equipment removal services in Plano and across the surrounding Dallas-Fort Worth metroplex, working with facility owners, general contractors, electrical contractors and property managers who need switchgear, panelboards, transfer switches, busway and related distribution equipment safely removed, disconnected and taken out of a building. This page walks through the project factors that most often determine schedule, cost and complexity, so a facility team requesting a quote can plan accordingly.
What “Electrical Gear” Removal Actually Involves
Electrical equipment removal covers a wide range of assemblies, and the scope changes significantly depending on what is actually installed. Common categories include:
- Low-voltage and medium-voltage switchgear, including drawout circuit breaker lineups such as Square D / Schneider Electric MasterPact NT and NW breakers, Eaton Magnum DS and DSII switchgear, GE/ABB AK and AKR breakers, and Siemens WL and SB frame equipment
If you have a project coming up, use the form below to tell our team about the facility, equipment and schedule.
- Distribution switchboards and panelboards, including Square D I-Line and PowerPact assemblies, Eaton Pow-R-Line panelboards, and Siemens Sentron boards
- Automatic and manual transfer switches, including ASCO Series 300, 4000 and 7000 transfer switches and Cummins/Onan PowerCommand-controlled ATS packages
- Busway and bus duct systems, such as Square D I-Line busway, Eaton Pow-R-Way, Starline track busway, Siemens Sentron and Schneider Canalis
- Motor control centers, load centers and associated feeder and branch circuit protection
Each of these categories carries different weight, footprint and connection complexity. A single MasterPact NW breaker section can weigh several hundred pounds and requires the drawout mechanism to be handled correctly before it can be lifted, while a full switchgear lineup rated at 2000A, 3000A or higher may span multiple bolted-together sections that need to be separated, de-bused and rigged individually. Busway removal introduces its own logistics, since long straight sections, elbows, tap boxes and plug-in units typically run overhead through ceilings, risers or electrical rooms and require staging and support before disconnection.
Why This Work Requires More Than a Standard Demolition Crew
Electrical gear removal sits at the intersection of electrical work and rigging, and both disciplines matter. Before any physical removal begins, the equipment has to be properly de-energized, locked out and verified dead, and any upstream or downstream connections have to be identified so removing one section does not create an unexpected condition elsewhere in the distribution system. On active or partially occupied buildings, this often means coordinating outage windows with the facility’s electrical contractor or engineer of record, particularly when a switchgear lineup or ATS also feeds equipment that has to remain in service during the project.
Once equipment is confirmed de-energized, the physical removal has to account for weight, access and clearance. Switchgear sections are typically anchored to housekeeping pads and interconnected with bus bar, and they are rarely designed to be moved as a single unit through a standard doorway. Getting a 480V lineup or a 5kV/13.8kV medium-voltage assembly out of an electrical room frequently requires disassembly into transportable sections, protection of adjacent finishes and equipment, and rigging equipment sized to the specific load and path, whether that is a pallet jack and dollies for lighter panelboards or a forklift, gantry or crane pick for heavier switchgear and transformer-adjacent equipment.

Working Around Active Operations and Occupied Buildings
Little electrical equipment removal happens in a building that is completely empty. Corporate offices, telecommunications facilities, manufacturing plants and data center support spaces in the Plano area are often still operating on adjacent circuits, floors or systems while a specific piece of equipment is being replaced or removed. That reality shapes several parts of the plan:
- Establishing clear work zones and barricading around the removal area so building occupants, other trades and operations staff are not exposed to an active work path
- Sequencing removal so critical loads, life-safety systems and IT infrastructure retain power throughout the project unless a planned outage has been scheduled and communicated in advance
- Coordinating temporary power or bypass arrangements when a transfer switch or main switchgear section that feeds essential loads is being replaced
- Managing noise, dust and material movement in a way that does not disrupt tenants, production lines or data hall operations
Buildings with raised floors, tight electrical rooms, or equipment located on upper floors or in below-grade vaults add another layer of planning, since the removal path itself, not just the equipment, often determines how the project has to be sequenced.
Access, Rigging and Site Conditions in Electrical Rooms
Electrical rooms are rarely built with future equipment removal in mind. Narrow doorways, low ceiling clearances, adjacent live equipment and limited maneuvering space are common conditions, and each one affects how a switchgear lineup, transformer or busway run actually comes out of the building. Before scheduling a removal, it helps to document:
- Door and corridor widths along the intended removal path
- Floor loading capacity, particularly on upper floors or mezzanines
- Ceiling height and any overhead obstructions such as ductwork, sprinkler mains or cable tray that could interfere with rigging
- Distance from the equipment to a loading dock, freight elevator or exterior opening
- Whether equipment is bolted to a housekeeping pad, embedded in a concrete pit, or otherwise permanently anchored
For medium-voltage equipment, arc-flash boundaries and equipment condition also factor into the removal plan, since older gear that has not been recently serviced may require additional caution during disconnection and handling. A pre-project site walk is typically the fastest way to identify these conditions before they become a schedule surprise.
Asset Recovery Potential in Switchgear and Distribution Equipment
Electrical distribution equipment is one of the more consistently recoverable categories of industrial equipment, and that potential is worth evaluating before a lineup is scrapped outright. Drawout breakers such as MasterPact NT/NW, Magnum DS and DSII, and AK/AKR frames see ongoing demand in the secondary market from facilities maintaining older switchgear lineups, replacing failed breakers, or standardizing spare parts. Complete switchgear sections, panelboards, busway runs and transfer switches in usable condition can sometimes be resold or reused rather than scrapped, and the copper and aluminum content in bus bar, wiring and enclosures carries recyclable commodity value even when equipment is not a resale candidate.
Several factors affect what a given piece of equipment is actually worth in the secondary market: manufacturer and model family, frame size and ampacity, voltage class, completeness (including trip units, drawout mechanisms and accessories), physical condition, and how the equipment was removed. Breakers and switchgear sections that are carefully de-energized, disconnected and rigged out intact generally hold more resale value than equipment that is cut apart or damaged during removal. As part of a removal project, our team evaluates what is on site and can advise on realistic disposition paths, whether that means resale, reuse, scrap recycling or a combination depending on what is found once equipment is inspected. Recovered value can help offset a portion of the overall project cost, though not every component will have resale value.
Automatic Transfer Switches and Standby Power Equipment
Transfer switches often get removed alongside switchgear during a facility upgrade, generator replacement or full electrical system overhaul. ASCO Series 300, 4000 and 7000 transfer switches, along with Cummins/Onan PowerCommand-controlled units and Kohler commercial ATS families, are examples of the equipment found in office, healthcare-adjacent, telecommunications and light industrial facilities. Removing an ATS involves the same de-energization and disconnection discipline as switchgear work, plus attention to the control wiring and interlocks that coordinate switching between utility and standby power sources. Where a facility is replacing standby generation or consolidating emergency power systems, transfer switch removal is frequently scheduled in the same outage window as generator or switchgear work to minimize the number of planned service interruptions.
Recycling, Scrap Handling and Material Segregation
Not every component removed from an electrical room is a resale candidate, and a responsible removal plan accounts for that from the start. Copper conductor, bus bar and wiring are typically segregated from steel enclosures and mixed scrap so each material stream can be recycled at appropriate value rather than combined into lower-grade scrap. Equipment containing PCBs, such as certain older transformers or capacitors, requires identification and handling in accordance with applicable federal and state requirements, and any such equipment encountered during a project should be flagged and addressed as part of the overall plan rather than treated as routine scrap.
Site Restoration and Turnover Requirements
Once equipment is removed, most projects require some level of site restoration before the space is considered complete. This can include patching housekeeping pads, capping abandoned conduit, removing anchor bolts and bracing, and returning the electrical room or mechanical space to a condition suitable for new equipment installation or general building use. Facility owners preparing a space for lease turnover, tenant improvement or a new equipment installation should communicate the expected end condition early, since restoration scope affects both schedule and cost.
Planning a Project in the Plano and North Texas Market
Plano’s position within the broader Dallas-Fort Worth corridor means many facilities here operate on schedules tied to corporate real estate, IT infrastructure or manufacturing decisions made at a regional or national level. Electrical equipment removal projects frequently need to align with a lease expiration, a scheduled capital upgrade, or a broader facility consolidation timeline. USA Decom provides electrical equipment removal services throughout Plano and nearby North Texas communities, including Frisco, Allen, McKinney, Richardson, Carrollton, Addison and the greater Dallas area, working around the access, scheduling and disposition considerations described above.

What to Include When You Reach Out
Before requesting a quote, it helps to gather some basic information about the equipment and the site. Useful details include the manufacturer and model or frame size of the switchgear, breakers, transfer switches or busway involved; the approximate voltage and ampacity ratings; whether the equipment is currently energized or already de-energized; the location within the building (floor, electrical room, vault); access conditions along the removal path; and any schedule constraints tied to a lease, shutdown or ongoing construction. Photographs of the equipment and nameplate data are especially helpful for evaluating asset recovery potential before a site visit.
Tell Us About Your Project
If you’re planning to remove switchgear, panelboards, transfer switches, busway or other electrical distribution equipment from a facility in Plano or elsewhere in North Texas, use the form below to tell our team about the equipment involved, the facility type, site access conditions and your target schedule. Include manufacturer and model information where available, along with photos if you have them, so we can evaluate the scope and any asset recovery potential as part of our review.

