The Electrical Gear Behind Irving’s Growth Doesn’t Disappear on Its Own
Irving and the Las Colinas corridor have seen substantial office, corporate campus and data center development over the past several years, and that growth runs on electrical infrastructure most tenants and visitors never see. Every new campus, tower renovation or data hall expansion depends on medium- and low-voltage switchgear, panelboards, busway, transfer switches and power distribution equipment installed behind mechanical room walls and inside electrical closets.
That same development cycle creates an ongoing need to remove electrical gear that’s being retired, replaced or made surplus. Office towers along the Las Colinas corridor get re-tenanted with different load profiles. Corporate campuses upgrade aging switchboards ahead of a lease turnover. Data center operators swap out earlier-generation PDUs, RPPs and switchgear lineups as facilities are refreshed or repowered. Manufacturing and logistics buildings near DFW Airport replace panelboards that don’t match a new tenant’s electrical scope. In each of these situations, someone has to physically remove the equipment safely, on schedule, and without creating unnecessary risk to an active facility.
That’s the work USA Decom does. We remove de-energized electrical distribution equipment – switchgear, switchboards, panelboards, busway, transformers, automatic transfer switches and related gear – from commercial, industrial and data center facilities throughout Irving and the surrounding Dallas-Fort Worth market, and we evaluate the recovered equipment for resale, reuse or recycling where it makes sense to do so.
What “Electrical Equipment” Actually Means on a Removal Project
Electrical gear removal projects rarely involve a single piece of equipment. A typical scope includes some combination of:
- Low- and medium-voltage switchgear and switchboards, including drawout breaker lineups such as Eaton’s Magnum DS platform or comparable Square D Power-Zone and QED-series equipment
- Molded-case and insulated-case circuit breakers in panelboards and distribution sections
- Busway and bus duct systems, including Square D I-Line and I-Line II runs, Eaton Pow-R-Way, and similar plug-in or feeder busway
If you have a project coming up, use the form below to tell our team about the facility, equipment and schedule.
- Panelboards and load centers rated anywhere from 208V and 480V branch distribution up through 600V service equipment
- Automatic transfer switches (ATS) and bypass-isolation switches serving standby or emergency systems
- Power distribution units (PDUs) and remote power panels (RPPs) in data center white space
- Motor control centers, disconnects, and associated conduit, cable and grounding infrastructure
Every one of these categories has its own removal considerations. A drawout breaker lineup has to be de-energized, isolated, and its breakers racked out and physically separated from cubicle structures before the enclosure can be moved. Busway runs typically come down in sections, following the same plug-in joints and hanger points used during installation, just in reverse. Panelboards usually require disconnection of every branch circuit before the can and trim can be pulled from the wall. None of this is exotic work, but it requires people who understand how the equipment goes together, how it comes apart, and where the real hazards are.
Why This Work Is Different From General Demolition
Electrical distribution equipment sits at the center of a building’s power system, which means removal has to be sequenced around whatever else is happening on-site. A few things consistently shape the plan:
- Isolation and lockout requirements. Equipment must be confirmed de-energized and properly isolated before any disassembly begins, and the isolation plan needs to account for backfeed from generators, UPS systems or adjacent sections still in service.
- Arc-flash and shock hazards. Even de-energized gear can retain stored energy in capacitors or connected cable, and adjacent live sections common in occupied buildings require clear boundaries and qualified personnel.
- Weight and rigging. A single vertical section of low-voltage switchgear can weigh several thousand pounds. Moving it out of a mechanical or electrical room often means routing through door openings, freight elevators or temporary openings that were never designed with equipment removal in mind.
- Continuity of service. Most electrical rooms in an occupied building feed something that’s still running. Removal sequencing has to protect circuits that stay in service while isolating and removing the sections that don’t.
- Floor loading and access. Electrical rooms are frequently located in basements, on upper floors, or behind other equipment, which affects how gear gets rigged, skated or craned out of the building.
Planning around these factors is what separates a controlled removal from an improvised one, and it’s a large part of why facility owners and electrical contractors bring in a team that regularly handles this type of equipment rather than treating it as incidental demolition work.

Where This Work Shows Up Around Irving
Given the mix of building stock in Irving and Las Colinas, electrical equipment removal needs generally fall into a few categories:
- Office and corporate campus renovations. Office towers in Las Colinas and along the LBJ Freeway and State Highway 114 corridors go through tenant improvement work that can include replacing aging electrical distribution equipment as part of a base building upgrade.
- Data center equipment refreshes. As operators expand or reconfigure white space, earlier-generation switchgear, PDUs, RPPs and ATS equipment come out to make room for higher-density power distribution.
- Manufacturing and light industrial turnover. Facilities near DFW Airport and along the I-35E and SH 183 corridors that change tenants or production lines often require electrical scope demolition ahead of new equipment installation.
- Facility closures and consolidations. When a corporate location closes or an operation consolidates elsewhere, the electrical infrastructure – switchgear, panelboards, busway, ATS equipment – typically needs to come out before the space can be turned over to a landlord or redeveloped.
Asset Recovery: Not Everything Belongs in a Scrap Bin
A meaningful part of most electrical equipment removal projects is figuring out what should be recycled for material value and what still has functional value to another buyer. Drawout circuit breakers, complete switchgear sections, transfer switches and busway are commonly reused in the secondary equipment market when they’re removed intact and in good physical condition.
Several factors affect whether a piece of gear is a realistic resale candidate:
- Manufacturer and family. Recognized product lines – Eaton Magnum and Series C breakers, Square D I-Line and PowerPact equipment, GE/ABB AKR and Spectra gear, Siemens WL and Sentron equipment – tend to have an established secondary market and available replacement parts, which supports resale demand.
- Voltage and amperage rating. Common service-entrance and distribution ratings (400A, 800A, 1200A, 2000A and similar frame sizes at 208V-600V) generally see more secondary-market interest than unusual or highly customized configurations.
- Completeness and condition. Breakers, trip units, cell structures, cabling and nameplates that stay together and undamaged during removal preserve value that gets lost when equipment is cut apart or handled roughly.
- Age and remaining service life. Newer or lightly used equipment generally holds more resale interest, though many older draw-out breaker platforms remain in active demand because they’re still supported and widely used.
- Quantity. A full switchgear lineup or a complete busway run is often more valuable to a secondary buyer than a single isolated section.
We evaluate recovered switchgear, breakers, busway, transformers and transfer switches against current secondary-market conditions and identify what can reasonably be resold, reused or recycled for material value. Recoverable value from this equipment can help offset a portion of removal costs, though not every piece of equipment will have resale value, and recovered value should not be assumed to cover the full project cost.

What We Need to Know Before We Can Scope the Project
Every quote starts with a basic understanding of what’s in the room and what condition it’s in. Before reaching out, it helps to have a general sense of:
- Facility type and location – office, industrial, data center, manufacturing, or other commercial space in Irving or the surrounding metro
- Equipment involved – switchgear, switchboards, panelboards, busway, ATS equipment, PDUs/RPPs, or a mix
- Manufacturer and approximate ratings – even general information (voltage, amperage, manufacturer name on the nameplate) is useful
- Quantity and scope – a single panelboard, a full electrical room, or a multi-floor distribution system
- Operational status – is the gear already de-energized, or still in service and awaiting a cutover date
- Site access conditions – floor level, elevator access, door widths, and any known rigging constraints
- Target schedule – tied to a lease expiration, tenant move-in date, or construction milestone
- Photographs – nameplate photos and general room photos speed up the evaluation considerably
We don’t need a perfect inventory to start the conversation. A walk-through description and a handful of photos are usually enough for us to ask the right follow-up questions and put together a realistic scope.
Serving Irving and the Surrounding DFW Market
USA Decom provides electrical equipment removal services throughout Irving and the broader Dallas-Fort Worth metroplex, including Las Colinas, Grapevine, Coppell, Farmers Branch, Carrollton, Addison and the greater Dallas and Fort Worth business districts. Whether the project is a single-floor electrical room in a Las Colinas office tower or a multi-building campus retirement near DFW Airport, the planning approach is the same: understand the equipment, confirm isolation, sequence the removal around the active parts of the facility, and identify what’s worth recovering along the way.
Tell Us About Your Electrical Removal Project
If you’re planning to remove switchgear, panelboards, busway, transfer switches or other electrical distribution equipment from a facility in Irving or the surrounding area, use the form below to tell our team about the building, the equipment involved, and your target timeline. Include the manufacturer and ratings if you have them, along with photos of the equipment and access route where possible – that information helps us give you a realistic read on scope, schedule and what may be recoverable before the project moves forward.


