Data Center Equipment Removal in Dallas, Texas

Dallas-Fort Worth is one of the more established data center markets in the country, with colocation, enterprise and hyperscale facilities spread from downtown Dallas through Plano, Richardson, Irving and the surrounding suburbs. Facilities in this market — including carrier-neutral hubs like the Infomart in downtown Dallas — go through refresh cycles, lease turnovers, consolidations and facility retirements, and each of those events leaves behind generators, UPS systems, precision cooling units, switchgear, PDUs, server racks and IT equipment that has to come out safely, on schedule, and with a plan for what happens to it next.

USA Decom performs targeted equipment removal inside operating and decommissioned data centers throughout the Dallas metro. This is different from a full facility decommissioning or white space teardown — it’s focused, system-by-system removal of the mechanical, electrical and IT infrastructure a facility no longer needs, whether that’s a single UPS replacement, a generator swap, or a room full of cooling and power gear coming out ahead of a lease turnover.

Why Data Centers in Dallas Need Targeted Equipment Removal

Not every project is a full shutdown. A colocation provider in the Infomart corridor might be swapping out an aging UPS fleet while the rest of the facility stays live. An enterprise IT team consolidating into a colocation suite in Plano may need legacy servers, switches and racks pulled from a smaller on-premise room. A facility exiting a lease in the Telecom Corridor around Richardson might need generators, chillers and electrical gear removed and the space restored to base building condition for the landlord.

In each case, the equipment itself has value, weight, hazards and logistics that have to be planned around — and the surrounding facility usually stays partially or fully operational during the work. That combination is what separates targeted equipment removal from a simple demolition job.

If you have a project coming up, use the form below to tell our team about the facility, equipment and schedule.

Equipment We Remove from Dallas-Area Data Centers

Our scope on these projects typically covers some combination of the following systems:

Generators and backup power — diesel standby generators from manufacturers like CAT, Cummins, Kohler and Generac, ranging from smaller building-standby units up to larger multi-megawatt sets serving enterprise or colocation facilities, along with day tanks, fuel piping and paralleling switchgear.

UPS systems and batteries — three-phase UPS units such as Eaton’s 9395 and 93PM families, Vertiv/Liebert EXL, eXM and APM systems, and APC/Schneider Galaxy units, along with the associated VRLA or lithium-ion battery strings. Eaton 93PM systems, for example, use a supplemental low-voltage shunt-trip signal to the battery disconnect device that has to be accounted for before the unit is de-energized — one of several coordination points that varies by manufacturer and model. Battery cabinets add substantial weight and handling requirements beyond the UPS module itself.

Precision cooling — CRAC and CRAH units from Vertiv/Liebert, STULZ, Data Aire and Schneider/APC Uniflair, including refrigerant recovery, condenser disconnection and, where applicable, glycol or chilled-water piping isolation.

Electrical distribution and switchgear — low- and medium-voltage gear from Square D/Schneider, Eaton/Cutler-Hammer, Siemens/ITE, GE/ABB, along with automatic transfer switches from ASCO and Russelectric, busway systems such as Starline, and the PDUs and RPPs (Vertiv/Liebert, Eaton/Powerware, APC/Schneider, PDI) that distribute power to the floor.

Racks, containment and raised floor infrastructure — server racks and containment systems from APC, Chatsworth/CPI, Panduit and Rittal, and Tate-style raised floor panels and pedestals where a room is being cleared to slab.

IT and network hardware — servers, storage and networking equipment from Dell, Dell EMC, HPE, Cisco, IBM, Lenovo, NetApp, Pure Storage, Supermicro, Arista and Juniper, typically staged and packaged for resale, recycling or destruction depending on the customer’s data-handling requirements.

Planning the Shutdown Sequence

Every removal project starts with understanding what stays live and what comes out. On a partial refresh — say, replacing a Liebert EXL UPS bank while the rest of the room continues running load — the sequence has to account for load transfer, bypass paths, and coordination with facility staff or the customer’s electrical engineer before anything is de-energized. Lockout/tagout procedures are applied to every circuit, generator and mechanical system involved, and battery strings are handled as a distinct step because of their stored energy, weight, and the ventilation and spill-containment considerations that come with VRLA and lithium-ion chemistries.

For cooling equipment, refrigerant has to be properly recovered before any CRAC or CRAH unit is disconnected, and glycol or chilled-water loops need to be drained and isolated in a way that doesn’t affect systems that remain in service. On active floors, this often means running the removal work in phases — pulling one unit or one row at a time — so redundancy and cooling capacity for the remaining IT load stay intact throughout the project.

Facility access shapes the plan as much as the equipment itself. Multi-tenant colocation buildings have loading dock schedules, freight elevator reservations and security escort requirements; enterprise data centers built into office towers may have tighter floor-to-floor clearances and weight limits that dictate how equipment gets broken down and moved. We build the rigging and logistics plan around the specific building rather than assuming every facility handles freight the same way.

Asset Recovery: Making Disposition Part of the Plan

One of the most consequential decisions on any equipment removal project isn’t how something gets taken out — it’s what happens to it afterward. Generators, UPS modules, precision cooling units, switchgear and racking that are still functional often have real value in the secondary market, and treating disposition as an afterthought can mean scrapping equipment that should have been evaluated for resale.

Before removal begins, we look at what’s coming out and how it’s likely to be handled:

  • Resale and reuse — Functioning generators, UPS systems, PDUs, transformers and racking with remaining service life are candidates for the used equipment market. Manufacturer, model, capacity, age, condition and completeness (including manuals, remote monitoring cards and spare parts) all affect whether a unit is a resale candidate or better suited for parts recovery.
  • Component and parts recovery — Equipment that isn’t a clean resale candidate may still have recoverable components — control boards, breakers, transformers, copper windings or battery cells — worth pulling before the rest goes to scrap.
  • Metals recycling — Steel racks, copper busway and wiring, and aluminum and structural components from removed equipment carry commodity value even when the equipment itself has reached end of service life.
  • IT asset disposition considerations — Servers, storage arrays and networking gear frequently retain resale or component value, but data-bearing devices also carry chain-of-custody and sanitization requirements that need to be addressed as part of the overall plan, separate from the physical removal work.
  • Responsible disposal — Anything without recovery value — obsolete cooling components, damaged batteries, non-recyclable materials — still needs to be handled and disposed of properly rather than left for the facility to manage after the crew leaves.

None of this changes the sequencing or safety requirements of the removal itself, but knowing in advance what’s staying together for resale versus what’s being broken down for scrap affects staging, packaging and how equipment is loaded for transport. Recoverable value can help offset a portion of the overall project cost, though the amount varies significantly by equipment type, age, condition and current secondary-market demand — it isn’t something we promise a number on before evaluating the actual equipment.

Logistics, Loading and Transportation

Getting equipment out of the building is only half the job. UPS cabinets, generators and switchgear are heavy, often oversized, and frequently located on upper floors or in below-grade mechanical rooms that weren’t designed with future removal in mind. Rigging plans account for equipment weight and dimensions, door and elevator clearances, floor loading limits, and whether disassembly is required to move a unit safely.

Once equipment is staged, freight requirements vary by disposition path — a UPS module headed for resale needs to be packaged and secured differently than components going to a recycling processor. For projects involving multiple equipment types across a building, we coordinate loadout so functioning resale equipment, scrap metal and IT assets each move through the correct channel rather than getting mixed together at the dock.

Project Spotlight: Data Hall Equipment Refresh

Projects of this type often follow a similar pattern. In one scope of work, our team worked through a UPS and cooling refresh in an operating data hall for a colocation-style facility. The removal covered a bank of legacy three-phase UPS units and associated battery strings, several precision cooling units that had reached end of service life, and a section of PDUs no longer matched to the current load configuration — all while the surrounding rows remained live and serving customer equipment.

The sequence started with load transfer planning in coordination with the facility’s engineering team, followed by staged lockout/tagout of each system before disconnection. Battery strings were removed and packaged separately given their weight and handling requirements, refrigerant was recovered from the cooling units ahead of disconnection, and the UPS modules — still within useful service life — were evaluated and staged for resale rather than scrap. Metal racking, PDU enclosures and cabling that had reached end of life were segregated for recycling. Work of this kind typically moves in phases tied to the customer’s shutdown windows, so redundancy for the equipment that stays in service isn’t compromised at any point during the project.

Nearby Markets We Serve

In addition to Dallas proper, USA Decom provides data center equipment removal services throughout the surrounding metro, including Fort Worth, Plano, Irving, Richardson, Arlington, Garland and the broader North Texas corridor. Facilities in these submarkets — from downtown colocation buildings to suburban enterprise data centers and telecom hubs — face similar refresh, consolidation and lease-turnover events that drive the need for targeted equipment removal.

What to Include When You Reach Out

To evaluate a Dallas-area equipment removal project, it helps to know the type of facility, whether it’s active or already offline, which systems need to come out (generators, UPS, cooling, electrical, racks, IT equipment or a combination), approximate quantities and manufacturers where known, site access conditions, and your target schedule or shutdown window. If you have equipment you believe still has resale value, let us know — photographs are especially useful for evaluating condition and completeness.

Use the form below to tell our team about the facility, the equipment involved and your timeline, and we’ll follow up to discuss scope, logistics and next steps.

Related Posts